The CLM colloid mill is specifically designed for production of highly stable colloid solutions, super-fine suspensions and emulsions. The mill applies the wet milling principle due to the rotor and stator cones’ larger gap width at the input and smaller gap width at the outlet.
Additionally, the complex geometry of the rotor surface creates intensive turbulence to shear particles.
The product in the mill is ground between the rotating and stationary calibrated cylindrical radially skewed teeth of the rotor and stator.
The centrifugal force and high velocity of the rotor relative to the fixed stator cause liquid and semi-liquid materials to become homogenic and finely dispersed.
The mill simultaneously disperses and homogenizes materials.
A heat jacket allows to apply or dissipate heat to or from the grinding zone.
The mill features high performance capacity, allows to produce highly stable emulsions, as well as colloidal suspensions, ensures high degree of homogenization and particle size to 1 micron.
Processes are intensified by 100 – 600% compared to agitator.
Besides, the device creates cavitation, i.e. explosion of caverns by internal pressure.
The mill can be retrofitted into existing production lines.
For high quality grinding the product must enter the mill in certain proportions at constant rate.
The degree of granulation and pumping qualities may vary depending on the mechanical properties of the material and the carrier phase.
No
PARAMETER
CLM – 22.2
CLM – 18.1
CLM – 4.1
CLM – 05.3
1
***Capacity rated, m³/hour, up to.
22
18
4
1,8
2
Operating pressure, bar.
0,5
0,5
0,5
0,5
3
Rotation speed, RPM
3 000
3 000
3 000
3 000
4
**Max heat carrier temperature, °C
160
160
160
160
5
**Minimum coolant temperature, °C
-4
-4
-4
-4
6
Dispersion, micron
<50
<50
<50
<50
7
Nominal pressure/suction bore diameter, mm
80/120
80/80
32/65
32/32
8
Drive power, kW
55
11
5,5
3
9
*Dimensions, mm
– length
– width
– height
1440
430
650
1000
400
460
960
310
400
960
310
400
10
Weight, kg
490
135
125
125
Note.
* – Dimensions are driven assembly.
** – If necessary, the product can be either heated or cooled to a desired temperature.
*** – Depending on the physical and chemical characteristics of the product capacity may vary.
The main advantages of the wet grinding GlobeCore colloid mills are:
Modern design and high quality of the device
Competitive price
Competent engineering consulting
Fast production of the order
The efficiency and speed of mixing at times more than a turbine agitator.
Savings on storage capacity compared with a turbine agitator – colloid mill built into a production line and does not require additional tanks.
Stability of the mix to stratification
Heating/cooling jacket
High-tech production lines and qualified staff (over 200) allows to expedite orders
Ability to adjust the gap of the grinding zone without the need to remove the device from the production line
Grinding to 1 micron
Component parts from universally recognized manufacturers
Operating temperature range from -30 С° to 180 С°
Optional soundproofing
Clients speak about GlobeCore mills:
Mr. Shekanabo, the United Republic of Tanzania:
“I can only say good things about GlobeCore mills. After seeing the production facility, I had no doubts that this is a serious and reliable company with professional staff, and the system works like a clock. Of course, the production itself seems complicated, but the equipment is powerful and rugged.”
Mr. Patel, the United Republic of Tanzania:
“I want to wish GlobeCore success in the future and I think we will maintain our cooperation for many more years. May you have as many successful products and new developments as possible.”
Laboratory homogenizer for sample preparation is an important piece of equipment that makes foods with new flavors, produces medicines and helps in chemical research.
Let’s consider the use of this device in different industries in detail. To compete in the food product market, many manufacturers develop new recipes, new products with improved flavors and longer shelf life, etc. At the stage of research it does not make...
Laboratory equipment, despite its apparent simplicity, plays a crucial role in industrial processes.
To understand this, recall the whole process of designing machines and mechanisms for the production of consumer products, from the beginning. In the first stage a prototype of the equipment is produced, which is then subjected to all kinds of tests, simulating the situations that may arise during industrial operation.
Colloid Mills. Colloid pulverization is such processing of materials which produces partices of colloidal sizes (several micron and smaller).
At certain conditions, this degree of pulverization can be achieved with just about any industrial grinding equipment. But if the process is considered from the economic and technological viewpoints, it becomes apparent such tasks are best performed by colloid mills. There is no coagulation of particles in the...
Colloid milling is crushing of a product to the size of colloid particles (from a few micron to fractions of a micron). If certain conditions are created, this product can be produced in virtually any crushing plant, but the use of colloid mills is the most economical and technologically justified method.
The explanation is quite simple. Particles of colloidal size tend to gravitate to each other, after...
Water-bitumen emulsion is highly appreciated by building and road construction companies. This is due to its ease and safety of use in comparison with the mixtures based on solvents of and from petroleum products such as kerosene. As a rule, water-bitumen emulsion is obtained by blending liquid bitumen with water and special emulsifiers and acids.
Having years of experience in designing and building blending machines and bitumen emulsion units, GlоbeCоre is...
Chemical, food, construction and many other industries cannot do without the preparation of different suspensions, emulsions and colloid solutions. They include lubricating oil emulsions, fuel emulsions, polymer modified bitumen as well as a wide range of food fat emulsions. Additionally, many kinds of gels, creams, and pastes are included in this list, so the list is virtually endless.
To obtain high quality homogeneous multi-component mixtures and colloid solutions, the production facilities...
GlobeCore is a leading manufacturer of high quality equipment used for regeneration, restoration and production of bitumen emulsions and all possible polymer-modified industrial liquids. GlobeCore equipment has enjoyed sustained demand in more than seventy countries around the world.
Annually, GlobeCore produces several hundred units for emulsifying, dispersion, wet grinding and blending of solid and liquid substances. Each blending line or a separate machine delivered to a customer, is tested before leaving...
Bitumen emulsions are used for road surface treatment, soil reinforcement, and ground stabilization as well as for the construction of roads and highways. Bitumen emulsion usually consists of bitumen (50-70%) and water (30-50%). A special component known as an emulsifier (acidol, naphtha soap, sulphate soap) is added to bitumen emulsion to make it stable. The emulsifier is more expensive than bitumen though only 0.6-1.6% of emulsifier is required for bitumen...
Colloid mills are a very unique kind of industrial equipment. They are used for the grinding of road construction materials and perform the grinding through the effect of cavitating forces. These forces result from considerable centrifugal loads.
GlobeCore produces and supplies the domestic and international road construction industry with a wide range of equipment for the production of bitumen emulsions and modified bitumen products. The GlobeCore brand of equipment may vary...
A colloid mill is one of the most important parts of the equipment used in the blending of bitumen emulsion products. It grinds bitumen down to particles of between 1 and 3 microns while blending it with an emulsifier solution.
A unit for emulsion production consists of many separate units and sub-assembly parts that have their own peculiarities and provide for the overall operation of the colloid mill. The quality of...
GlobeCore manufactures advanced mills for superfine grinding, able to make powders, suspensions, sols and stable colloid solutions, as well as other highly dispersed materials. One of the most widespread materials made by superfine grinding is water-bitumen emulsion, widely used in road construction, water proofing of buildings and roofing. GlobeCore specializes in manufacturing of UVB type equipment, made specifically for water bitumen emulsion production.
The superfine grinding mills are made for intensive...
This website uses cookies so that we can provide you with the best user experience possible. Cookie information is stored in your browser and performs functions such as recognising you when you return to our website and helping our team to understand which sections of the website you find most interesting and useful.
Strictly Necessary Cookies
Strictly Necessary Cookie should be enabled at all times so that we can save your preferences for cookie settings.
If you disable this cookie, we will not be able to save your preferences. This means that every time you visit this website you will need to enable or disable cookies again.